Searching for: Gundam Parts + WATER DECALS / STICKERS products | Bandai gundam models kits premium shop online at Ampang, Selangor | Bandai Toy Shop @ Gundam.my. Our online shop offers wide range of Gundam model kits, Ultraman, Kamen Rider, Digimon Monster Amplified, Dragon Ball, One Piece Grand Ship, S.H.Figuarts etc, plastic kits and more

Quick View

SAVERM8.90

Water Decal for MG 1/100 00 QAN[T] Gundam

- Water Decal for MG 1/100 00 QAN[T] Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM8.90

Water Decal HG Beargguy III

- Water Decal for HG BEARGGUY III water decal

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM8.90

Water Decal HG 1/144 00 QAN[T] Gundam

- Water Decal for HG 1/144 00 QAN[T] Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM8.90

Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM11.00

[Water Decal][Bandai] Mobile Suit Gundam Iron Blooded Orphans #103

[Bandai] Mobile Suit Gundam Iron Blooded Orphans Water Decal #1 (GD103)

For HGIBO / NG 1/100 Barbatos

RM18.90

RM18.90 Add to cart

Quick View

SAVERM19.90

Water Decal for MG 1/100 RX-178 MK-II MK2 AEUG Gundam

- Water Decal for MG 1/100 RX-178 MK-II MK2 AEUG Gundam Water Decal

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 15 cm x 20 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM10.00

Minimum RM 3.00 Off	300 points
Maximum	To how many points maximum you can claim /100 = discount value in RM

Price Clear

Showing Gundam Parts + WATER DECALS / STICKERS product(s)