Searching for: Gundam Parts products | Bandai gundam models kits premium shop online at Ampang, Selangor | Bandai Toy Shop @ Gundam.my. Our online shop offers wide range of Gundam model kits, Ultraman, Kamen Rider, Digimon Monster Amplified, Dragon Ball, One Piece Grand Ship, S.H.Figuarts etc, plastic kits and more

Quick View

SAVERM8.09

1/144 Scale Over Flag Decal Sheet

Gundam decal sheet recommended for use on HG Over Flags, Union Flags and Union Flags Custom II Kits

RM3.90

RM3.90 Add to cart

Quick View

SAVERM8.09

[Bandai]1/144 scale Zeon Decal Sheet

1/144 Gundam decal sheet recommended for use on HGUC Zaku, Zaku II, Neo Zeong kits.

RM3.90

RM3.90 Add to cart

Quick View

SAVERM8.90

Water Decal HG 1/144 00 QAN[T] Gundam

- Water Decal for HG 1/144 00 QAN[T] Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM8.90

Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM17.18

Water Decal PG 1/60 FX-550 SKY GRASPER

- Water Decal for PG FX-550 SKY GRASPER water decal

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 21 cm x 24 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM18.80

RM18.80 Add to cart

Quick View

SAVERM13.98

Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam

- Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11.5 cm x 13.5 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunpla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM10.00

RM10.00 Add to cart

Quick View

SAVERM15.08

HG 1/144 STRIKE FREEDOM Metal Effect Water Decal

- Water Decal for HG 1/144 Strike Freedom Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 10 cm x 9 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM14.90

RM14.90 Add to cart

Quick View

SAVERM15.30

[Metal Part] MG 1/100 Hi-Nu Gundam Ver. Ka Metal Enhancement Part Set

All pictures shown are for illustration purpose only. Actual product may vary, kindly check from the list below to find out the actual product quantity. Index	Parts	Installation
1.	LED + 2 batteries x1	direct installation
2.	Vulcan Canon x2	drill 1.3mm hole, attached to point with minor cement
3.	Backpack + Calf thruster x4	drill 2.0mm hole, attached to point with minor cement
4.	Shoulder heavyarm screw x4	drill 1.0mm hole, attached to point with minor cement
5.	Forearm aviation hole x4	drill 1.0mm hole, attached to point with minor cement
6.	Metal hand joint cover (round shape) x4	Direct installation, attached to point with minor cement
7.	Chest Aviation hole x2	drill 2.5mm hole, attached to point with minor cement
8.	Metal knee joint cover (round shape) x4	drill 1.0mm hole, attached to point with minor cement
9.	Metal knee joint Hydraulic tube (round shape) x4	drill 1.0mm hole, attached to point with minor cement
10.	Knee and lower aviation hole x8	drill 3.0mm hole, attached to point with minor cement
11.	Shoulder Aviation hole x4	drill 2.0mm hole, attached to point with minor cement
7.	Arm Aviation hole x4	drill 2.0mm hole, attached to point with minor cement
8.	knee Aviation hole x4	drill 2.0mm hole, attached to point with minor cement
9.	Rear skirt Aviation hole x2	drill 2.0mm hole, attached to point with minor cement
10.	Metal hand joint cover (round shape) x4	drill 2.0mm hole, attached to point with minor cement
11.	Canon nozzle x1	drill 2.0mm hole, attached to point with minor cement
12.	Shield Aviation hole x12	drill 2.0mm hole, attached to point with minor cement
13.	Armor screw x10	direct installation, attached to point with minor cement
14.	Armor Screw 1.5mm x30	drill 2.0mm hole, attached to point with minor cement
15.	Armor aviation hole 1.6mm x15	drill 1.6mm hole, attached to point with minor cement
16.	Armor aviation hole 1.5mm x50	drill 2.0mm hole, attached to point with minor cement

Packages parts packed in different sealed plastic bags to avoid scratch, and easier installation (based on numbers tagged on the plastic bag)
Model kits in pictures are only for illustration of finished metal parts installation and excluded in the package.

Tools needed for assembling metal parts:

tweezer straight/angled
modelling kits cutter
metal cutter
metal wire
plastic model kits cement
magnifying glass

RM88.40

RM88.40 Add to cart

Quick View

SAVERM30.20

[Metal Part] RE 1/100 Gundam Mk III Metal Enhancement Part Set

All pictures shown are for illustration purpose only. Actual product may vary, kindly check from the list below to find out the actual product quantity.

Index Parts Installation

1. Rear Thruster x3 drill 2.5mm hole, attached to point with minor cement

2. Backpack thruster - x3 drill 3.5mm hole, attached to point with minor cement

3. Calf thruster - x2 drill 1.4mm hole, attached to point with minor cement

4. Armor aviation hole x15 drill 2.0mm hole, attached to point with minor cement

5. Single line Screw x30 drill 2.0mm hole, attached to point with minor cement

Packages parts packed in different sealed plastic bags to avoid scratch, and easier installation (based on numbers tagged on the plastic bag)
Model kits in pictures are only for illustration of finished metal parts installation and excluded in the package.

Tools needed for assembling metal parts:

tweezer straight/angled
modelling kits cutter
metal cutter
metal wire
plastic model kits cement
magnifying glass

RM73.50

RM73.50 Add to cart

Quick View

SAVERM45.20

[Metal Part] RE100 Gundam GP04G Gerbera Metal Enhancement Part Set

All pictures shown are for illustration purpose only. Actual product may vary, kindly check from the list below to find out the actual product quantity. Index	Parts	Installation
1.	Shoulder thruster x2	drill 1.5mm hole, attached to point with minor cement
2.	Lower shoulder thruster x8	drill 3.0mm hole, attached to point with minor cement
3.	Aviation hole on shoulder x3	drill 3.0mm hole, attached to point with minor cement
4.	Backpack thruster x15	drill 2.5mm hole, attached to point with minor cement
5.	Aviation hole on armor x15	drill 2.0mm hole, attached to point with minor cement
6.	Single line screw x30	drill 2.0mm hole, attached to point with minor cement

Packages parts packed in different sealed plastic bags to avoid scratch, and easier installation (based on numbers tagged on the plastic bag)
Model kits in pictures are only for illustration of finished metal parts installation and excluded in the package.

Tools needed for assembling metal parts:

tweezer straight/angled
modelling kits cutter
metal cutter
metal wire
plastic model kits cement
magnifying glass

RM58.50

RM58.50 Add to cart

Quick View

SAVERM3.60

[Metal Part] 4mm Zaku metallic Lens - Gold Colour

Diameter: 4.0mm
Gold colour lens
Thickness: 2.6mm
Material made: Copper
Suitable to fit on Bandai MG zaku 2.0 model kits

RM2.40

RM2.40 Add to cart

Quick View

SAVERM9.49

[Metal Part] Modelling Kits Gatling Gun Bullet Chain - Gold Colour

Modelling Kits Gatling Gun Bullet Chain
Width:8mm, Length 200mm
Suitable for installation on this kits: Unicorn Gundam gatling gun, Heavy armor gatling gun, MG 1/100 MS-07B-3 Gouf Custom gatlin gun
Gatling Gun NOT INCLUDED

RM8.50

RM8.50 Add to cart

Quick View

SAVERM9.49

[Metal Part] Modelling Kits Gatling Gun Bullet Chain - Silver Colour

Modelling Kits Gatling Gun Bullet Chain - silver colour chain
Width:8mm, Length 200mm
Suitable for installation on this kits: Unicorn Gundam gatling gun, Heavy armor gatling gun, MG 1/100 MS-07B-3 Gouf Custom gatlin gun
Gatling Gun NOT INCLUDED

RM8.50

RM8.50 Add to cart

Quick View

SAVERM9.49

[Metal Part] Modelling Kits Gatling Gun Bullet Chain - Black Colour

Modelling Kits Gatling Gun Bullet Chain - black colour chain
Width:8mm, Length 200mm
Suitable for installation on this kits: Unicorn Gundam gatling gun, Heavy armor gatling gun, MG 1/100 MS-07B-3 Gouf Custom gatlin gun
Gatling Gun NOT INCLUDED

RM8.50

RM8.50 Add to cart

Quick View

SAVERM16.30

MG Strike Gundam Metal Blade Part

MG Strike Gundam metal knife part
This unit consists of the metal knife only, no other model kit included.
More precise photo to come after photographer done capture the metal blade.

RM23.60

RM23.60 Add to cart

Quick View

SAVERM4.90

[Third Party] Action Base 1 for MG 1/100 and RG,HG 1/144 (Gray)

[TGF] Action Base MG/HG (GREY)

NOTE: Adapter is all 8mm in size.

RM15.00

RM15.00 Add to cart

Quick View

SAVERM10.10

[Third Party] Action Base 2 HG/RG (Clear) (1/144)

[TGF] Action Base HG/RG (Clear)

Suitable for every 1/144 scale and SD kit.

This is a Non-Bandai product.

RM9.80

RM9.80 Add to cart

Quick View

SAVERM8.90

Water Decal MG 1/144 Gundam Seed Blitz Gundam

- Water Decal for Water Decal MG 1/144 Gundam Seed Blitz Gundam

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View

SAVERM1.10

ABS Rod 240mm Long (mix 17pcs - circle, square) for DIY customize Model Kit

Material: ABS

Shapes: Round, Square, Annulus (With Holes), Square (With Holes)

Package Contents :

-----------------------

Round rod

1. Diameter : 0.5mm+- ,Length : 24cm+-

2. Diameter : 1.0mm+- ,Length : 24cm+-

3. Diameter : 2.0mm+- ,Length : 24cm+-

4. Diameter : 3.0mm+- ,Length : 24cm+-

5. Diameter : 5.0mm+- ,Length : 24cm+-

Square rod

1. Diameter : 1.0mm+- ,Length : 24cm+-

2. Diameter : 1.5mm+- ,Length : 24cm+-

3. Diameter : 2.0mm+- ,Length : 24cm+-

4. Diameter : 3.0mm+- ,Length : 24cm+-

5. Diameter : 5.0mm+- ,Length : 24cm+-

Annulus (With Holes)

1. Diameter : 2.0mm+- ,Length : 24cm+-

2. Diameter : 3.0mm+- ,Length : 24cm+-

3. Diameter : 4.0mm+- ,Length : 24cm+-

4. Diameter : 5.0mm+- ,Length : 24cm+-

Square (With Holes)

1. Diameter : 3.0mm+- ,Length : 24cm+-

2. Diameter : 4.0mm+- ,Length : 24cm+-

3. Diameter : 5.0mm+- ,Length : 24cm+-

RM13.90

RM13.90 Add to cart

Quick View

SAVERM4.90

[Third Party] Action Base 1 for MG 1/100 and RG,HG 1/144 (Clear Blue)

[TGF] Action Base MG/HG (CLEAR BLUE) (1/100,1/144)

RM15.00

RM15.00 Add to cart

Quick View

SAVERM9.00

[Metal Part] 50pcs - Armor Detail-up 1mm Metal Silver Bead Ball Parts For MG HG Gundam Model

50pcs per pack
Can be use as metal screw
To customize Armor kit to looks more detail and metal feel
For MG, RG or HG and 1/100 or 1/144 scales Gundam Model
Size : 1mm diameter

RM3.00

RM3.00 Add to cart

Quick View

SAVERM9.00

[Metal Part] 50pcs - Armor Detail-up 1.5mm Metal Silver Bead Ball Parts For MG HG Gundam Model

50pcs per pack
Can be use as metal screw
To customize Armor kit to looks more detail and metal feel
For MG, RG or HG and 1/100 or 1/144 scales Gundam Model
Size : 1.5 mm diameter

RM3.00

RM3.00 Add to cart

Quick View

SAVERM9.00

[Metal Part] 50pcs - Armor Detail-up 2mm Metal Silver Bead Ball Parts For MG HG Gundam Model

50pcs per pack
Can be use as metal screw
To customize Armor kit to looks more detail and metal feel
For MG, RG or HG and 1/100 or 1/144 scales Gundam Model
Size : 2mm diameter

RM3.00

RM3.00 Add to cart

Quick View

SAVERM8.90

Water Decal RG/ HG 1/144 00 QAN[T] Gundam

- Water Decal for RG/ HG 00 QAN[T] OO?Qan[T]

- Not pre-cut

- Best use with Mr. Hobby Mr. Mark Setter / Softer

- 11 cm x 15 cm

Tools:

* Decals

* Mr. Mark Setter (optional)

* Mr. Mark Softer (optional)

* Water

* Cotton buds

* Tweezers

* Paper towel

* Pen Knife

Instructions :

1. Again, cut out the design you want from the decal sheet

2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.

3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.

4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.

Water slide decals are activated by water. So it's important to store them away from liquid.

RM9.00

RM9.00 Add to cart

Quick View